PLC migration and modernization

Move legacy PLC programs onto current platforms

Altitude translates a program, or a single routine, onto another brand, controller or version, makes only the fixes the target needs to run it, and writes down every decision it made.

Translate MainProgram/Infeed to

Studio 5000 Infeed_Conveyor.L5X · Ladder

0 INFEED CONVEYOR Start and stop seal-in, held off until both servos are ready. Start_PB Conveyor_Run Stop_PB Servos_Ready Conveyor_Run 1 JAM DETECTION A case held on the jam eye for 3 s times out the jam timer. Conveyor_Run Jam_Eye TON Timer On Delay Timer Jam_Timer Preset 3000 Accum 0 2 Jam_Timer.DN Jam_Alarm L

TIA Portal Infeed.scl · SCL

1// Infeed conveyor: start and stop seal-in2"Conveyor_Run" := ("Start_PB" OR "Conveyor_Run")3 AND NOT "Stop_PB" AND "Servos_Ready";4 5// Jam detection: 3 s on the jam eye6"Jam_Timer"(IN := "Conveyor_Run" AND "Jam_Eye", PT := T#3S);7 8// Jam alarm9IF "Jam_Timer".Q THEN10 "Jam_Alarm" := TRUE;11END_IF;

TwinCAT 3 Infeed.TcPOU · Structured text

1// Infeed conveyor: start and stop seal-in2Conveyor_Run := (Start_PB OR Conveyor_Run)3 AND NOT Stop_PB AND Servos_Ready;4 5// Jam detection: 3 s on the jam eye6Jam_Timer(IN := Conveyor_Run AND Jam_Eye, PT := T#3S);7 8// Jam alarm9IF Jam_Timer.Q THEN10 Jam_Alarm := TRUE;11END_IF

Translation report

Coverage 3 of 3 rungs translated

Decision Jam_Timer.DN is read as the IEC timer’s Q output

Address map 7 tags mapped, names kept

How it works

Step by step

  1. 1

    Bring the source

    An export from PLC-5, SLC 500, MicroLogix, Logix, STEP 7, TIA Portal or TwinCAT, or even a printout of the ladder, transcribed rung by rung first.

  2. 2

    Translate

    Translators carry SLC 500, MicroLogix and PLC-5 onto Logix, and move programs between Logix, TIA Portal and TwinCAT 3. Anything else is converted routine by routine.

  3. 3

    Fix what the target needs

    Each flag the translation raises is resolved in the target’s own instructions, or written out for the engineer at its place.

  4. 4

    Review the report

    Coverage, every decision and every flag, with an address map of where each tag and I/O point went.

What carries across

The translation keeps the program running the way it ran, in the target’s own instructions, and writes a report of every decision beside it.

  • Task timing, with periodic tasks as tasks or cyclic interrupts of their own
  • PID, PIDE and alarm instructions, ported from their documented behavior
  • Motion, on PLCopen blocks
  • I/O modules, matched to current modules of the same electrical kind
  • Names, kept wherever the target allows them
Infeed_TIA › Translation report.md Written beside the target

Coverage

3 of 3 rungs

Flags left

None

Tags mapped

7

Decisions

  • •Jam_Timer.DN is read as the IEC timer’s Q output.
  • •The 3000 ms preset is written as T#3S.
  • •MainTask’s period is kept as OB1’s cycle.

Address map

TagLogixTIA PortalAddress
Start_PB Local:1:I.Data.0 "Start_PB" %I0.0
Stop_PB Local:1:I.Data.1 "Stop_PB" %I0.1
Jam_Eye Local:1:I.Data.4 "Jam_Eye" %I0.4
Conveyor_Run Local:2:O.Data.0 "Conveyor_Run" %Q0.0
Jam_Timer TIMER "Jam_Timer" TON_TIME

From

  • PLC-5
  • SLC 500
  • MicroLogix
  • Older Logix controllers
  • S5
  • S7-300
  • S7-400
  • STEP 7 Classic
  • TwinCAT 2
  • Concept
  • PL7
  • Mitsubishi
  • Printouts

To

  • Studio 5000 Logix
  • TIA Portal
  • TwinCAT 3

FAQ

Questions teams ask first

Does it change the original program?
No. The translation is written beside the source, in a target named for the machine, and the source stays as it was.
Can it convert one routine instead of a whole controller?
Yes. A routine, block, Add-On Instruction or data type translates on its own, with its signals passed through its interface.
Can it work from a printout?
Yes. A printout is transcribed rung by rung, checked against the printout, and converted from the transcript.
Can it move a Logix project onto a newer controller?
Yes. It changes the project’s own .L5X for the new controller or version, or a copy where you ask for one.

Keep exploring

More ways teams use Altitude

See it on the work your team does every day

We'll walk through the workflows that matter most to your team, on the PLC, robot and HMI platforms you run, from review and troubleshooting to documents and migration.